Resources

Hall-Effect Thickness Gauge Articles

In short

Practical articles on wall thickness measurement of bottles, jars, tubes, preforms and other non-magnetic containers. For the full picture of the gauge itself, start with the ten-chapter guide.

14 November 2026

Blow Molding Wall Thickness and Where Bottles Go Thin

Where blow molded bottles go thin, and how wall thickness control, parison programming and in-process measurement help you find those zones.

Read the article

14 November 2026

How to Find the Thinnest Point on a Blow-Molded Bottle

How to find the thinnest point on a blow-molded bottle by marking risk zones and scanning each one, instead of relying on a mid-body reading.

Read the article

14 November 2026

Bottle Base Thickness Checks at the Push-Up and Heel

Bottle base thickness checks at the push-up and heel find thin spots that a mid-body wall reading will miss, using the same marks on every bottle.

Read the article

14 November 2026

Bottle Wall Thickness vs Top-Load and Drop Strength

Bottle wall thickness relates to top-load and drop strength, but those tests are separate. A thickness gauge does not measure top-load or drop performance.

Read the article

14 November 2026

Why Hall-Effect Thickness Readings Drift on Curves

Hall-effect thickness readings can drift on curves and ribs when the ball or probe is not seated squarely, so those zones need a slower, more careful scan.

Read the article

14 November 2026

Bottle Wall Thickness Tolerance on a Specification Drawing

A bottle wall thickness tolerance on a specification drawing should name the zone, the method and the agreed limit, without borrowing a generic figure.

Read the article

14 November 2026

SPC for Bottle Wall Thickness in Blow Molding

SPC for bottle wall thickness uses control charts on the same marked zones, without turning an unverified number into a control limit.

Read the article

14 November 2026

Wall Thickness on Oval and Rectangular Plastic Containers

Wall thickness on oval and rectangular plastic containers should be marked on the wide faces, corners and heels, not only at one mid-panel point.

Read the article

12 November 2026

LDPE Bottle Wall Thickness and Soft-Wall Container Checks

LDPE bottle wall thickness decides how a squeeze bottle dispenses and holds up. See where soft walls run thin and how to hold and mark them for checks.

Read the article

12 November 2026

Incoming Bottle Wall Thickness Inspection for Brand Owners

Incoming bottle wall thickness inspection works when buyer and supplier agree on points, limits and sampling first. How to set it up and settle disputes.

Read the article

12 November 2026

Bottle Wall Thickness Test Video and What to Tell Us First

A bottle wall thickness test video shows a Hall-effect gauge on a bottle like yours before you order. What to tell us, what the video shows and its limits.

Read the article

12 November 2026

Bottle Lightweighting and Wall Thickness Without Thin Spots

Bottle lightweighting takes resin out of the wall, so thin spots decide how far you can go. Use a wall thickness map to judge each weight reduction step.

Read the article

12 November 2026

Multilayer Bottle Wall Thickness and How Layers Are Checked

Multilayer bottle wall thickness has two parts: the whole wall and the barrier layer inside it. See why both matter and how labs check layer thickness.

Read the article

12 November 2026

Cosmetic Bottle and Jar Wall Thickness Measurement

Cosmetic bottle wall thickness shapes the look, feel and barrier of a pack. See where cosmetic bottles and jars vary and what to check before measuring.

Read the article

12 November 2026

Agrochemical Bottle Wall Thickness and Where They Go Thin

Agrochemical bottle wall thickness is decided at the handle, shoulder, corners and pinch-off. Where these containers go thin and how to build a wall map.

Read the article

12 November 2026

Hall-Effect Thickness Gauge for Distributors and Buyers

A Hall-effect thickness gauge for distributors: what to ask your end customer, which materials fit and which documents to request from KHT.

Read the article

12 November 2026

Magnetic Wall Thickness Gauge for Bottles vs Coating Gauges

A magnetic wall thickness gauge measures bottle walls with a steel ball inside. How it differs from a coating thickness gauge and which your parts need.

Read the article

8 November 2026

PET Bottle Wall Thickness and Where It Varies

Why PET bottle walls vary from shoulder to base, how to plan a repeatable wall-thickness map and what to check before using a Hall-effect gauge.

Read the article

8 November 2026

Thermoforming Wall Thickness in Cups and Trays

Why thermoformed cups and trays develop uneven walls, how plug and sheet conditions affect the distribution, and how to build a repeatable thickness map.

Read the article

27 October 2026

Wall Thickness Inspection Record: What to Log

A wall thickness inspection record logs bottle type and cavity, each marked point, the reading, calibration status, the operator and pass or fail.

Read the article

7 October 2026

HDPE Bottle Wall Thickness: Where It Varies

HDPE bottle wall thickness varies from neck to base. Learn where the thick and thin zones sit, what causes variation, and how to inspect without cutting.

Read the article

6 October 2026

How to Measure Tubing Wall Thickness

Measure tubing wall thickness without cutting: Hall-effect, ultrasonic and caliper methods, step by step, with a method-selection checklist.

Read the article

5 October 2026

How a Hall Effect Thickness Gauge Works

How a Hall-effect thickness gauge measures wall thickness using magnetic fields — physics, setup, materials, calibration, and ultrasonic comparison.

Read the article