Incoming bottle wall thickness inspection is the check a brand owner or filler runs on bottles as they arrive from the supplier. It works only when both sides have agreed in advance which points are measured, what the limits are and how a lot is sampled.
Why check wall thickness when bottles arrive?
A blow moulded bottle never has a uniform wall. The shoulder, panel, heel and base stretch differently, and the thin spots decide how a bottle stacks, squeezes and survives a drop.
Industry voluntary methods for plastic containers tie wall thickness consistency to permeation, oxygen ingress, water vapour loss and top-load strength. A filler who finds a thin heel at receipt avoids finding it later as a leaking or collapsed pack on the line.
The supplier usually measures at the blow moulder as well. Your incoming check is not a repeat of their work. It is your independent view of whether the lot you received matches what was agreed.
What to agree with your bottle supplier first
Most disputes about wall thickness start with a vague specification. Before the first delivery, put these points in writing with the supplier.
- The bottle drawing or reference sample the limits belong to
- The measurement points, named by zone, and how they are marked
- The limit for each zone, usually a minimum at the thinnest point
- How many bottles per lot are measured, and from which cavities
- The gauge type both sides use, and how it is checked before use
Voluntary methods for plastic containers leave acceptance criteria to the interested parties, so the numbers come from your agreement, not from a general standard. Mark the points on the bottle design and measure at those marks every time.
Want a test video on a bottle like yours? Tell us what you need to test. We test a similar material sample and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.
How to sample a lot without measuring every bottle
Acceptance sampling by attributes is covered by ISO 2859-1, which indexes sampling plans by an acceptance quality limit for lot-by-lot inspection. It also sets rules for switching to tightened inspection when results get worse and to reduced inspection when they stay good.
Pick the plan with your supplier and write the sample size and acceptance number into the agreement. This article does not suggest figures, because the right plan depends on lot size, risk and your history with that supplier.
On multi-cavity moulds, spread the sample across cavities. A thin spot often belongs to one cavity, and a sample that misses it can pass a lot with a weak cavity in it. Our plastic bottle measurement page lists the usual points on PET and HDPE bottles.
Keeping results comparable with the supplier
Two labs can measure the same bottle and disagree if they use different points, different conditioning or an unchecked gauge. Line these up before you compare numbers.
Test bottles at a consistent age and condition, and verify calibration of the equipment before the first bottle. For a Hall-effect gauge, our calibration chapter covers ball identification and the daily check.
Record each bottle so the result can be traced later. Our guide to the wall thickness inspection record lists the fields worth keeping, so they are not repeated here.
Where a Hall-effect gauge fits in receiving inspection
A Hall-effect bottle wall thickness gauge measures the wall without cutting the bottle. A steel target ball sits inside, the probe touches the outside, and the gauge shows live, maximum, minimum and average values while you scan a zone.
That makes it practical to find the thinnest point at each marked zone, then return the bottle to stock or keep it as a retained sample.
How to handle a wall thickness dispute
When an incoming check fails a lot, hold it and keep the measured bottles. Ask the supplier for their own results on the same lot, mould and cavities.
Re-measure jointly where possible, at the agreed marks and with both gauges checked against a known shim. Many disagreements turn out to be a different point or a missed calibration, not a different bottle.
If the thin spot is confirmed, the supplier has a clear zone and cavity to correct. A non-destructive check keeps the disputed bottles intact, so both sides can measure the same unit again.
Frequently asked questions
Should incoming inspection use the same points as the supplier?
Yes, as far as possible. Results can only be compared when both sides measure the same zones on the same bottle design.
Is wall thickness a pass or fail attribute?
It can be. If the agreement sets a minimum at the thinnest point, each bottle is either above or below it, which suits sampling by attributes.
Get a test video for your bottles
Tell us what you need to test, such as the material, the size and the test method. We test a similar material sample on the instrument you are looking at and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.
Questions about a model or a test? Email Amy Zhao, Export Manager, at info@halleffectthicknessgauge.com.