Article · 14 November 2026

SPC for Bottle Wall Thickness in Blow Molding

SPC for bottle wall thickness uses control charts on the same marked zones, without turning an unverified number into a control limit.

By Lim Xu, Export Manager

SPC for bottle wall thickness means charting the same marked zones over time so you can see drift, a cavity that is running thin, or a process change that has moved the wall. The chart is only as good as the marks and the sampling behind it. This page does not publish a control limit, because that figure has to come from your own data and your specification.

Chart the zone, not a mixed average

Give each risk zone its own chart, or a clearly labelled series, such as shoulder, mid-body, heel or pinch-off. An average of those zones can look stable while one zone is drifting toward its limit.

Keep cavities or heads separate if they can make different walls. A combined plot will hide a single cavity that is thin.

Start-up bottles and steady-run bottles should not sit on the same series unless the procedure says so. Label the points so a later reader can see which they were.

What the chart does not replace

A control chart does not replace the inspection record, and it does not invent the specification limit. What to write on the form is covered on the wall thickness inspection record page. How often to pull bottles is a sampling-plan decision, not a chart decoration.

Specification limits and control limits are not automatically the same thing. A process can be inside a loose specification and still be drifting, or it can sit close to a tight specification and still be in statistical control. Write down which kind of limit you are using.

We will not quote a sample control limit or a standard deviation target. Please confirm a starting chart design with us against the data you already have.

Want to see how a charted bottle is measured at the same marks? Tell us what you need to test. We test a similar material sample and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.

Measuring so the points stay comparable

Every point on the chart should be measured the same way, at the same marks, after a consistent bottle condition. A Hall-effect thickness gauge reads the wall without cutting the bottle, which makes it practical to measure retained samples and still keep the bottle.

Our Hall-effect bottle wall thickness gauge is built for non-destructive wall and base checks on non-magnetic plastics and glass. The measuring steps are in how to measure bottle wall thickness.

If the mould, the resin or the parison program changes, start a new phase on the chart or start a new chart. Mixing the old and new process on one line makes the later points hard to read.

Acting on a signal

When a point or a run of points signals a change, go back to that zone and that cavity before you change a process setting at random. A shift in the heel is not fixed by thickening the mid-body.

Record the action next to the chart, including any process change, so the next shift can see why the line moved.

Application notes for common bottles are on the plastic bottles application page.

Frequently asked questions

Can I plot one average wall thickness for the whole bottle?

You can, but it is a weak chart if the shoulder or heel can move on its own. Chart the zones that the specification names.

Will this page give me control limits to copy?

No. Limits have to come from your data and your specification. Please confirm a starting approach with us if you need help, but not a generic number.

Does a control chart replace sampling decisions?

No. The chart displays the points you already decided to take. The sampling plan still has to say when and from which cavity.

Get a test video for your bottles

Tell us what you need to test, such as the material, the size and the test method. We test a similar material sample on the instrument you are looking at and send you the video, so you do not need to ship a sample. If you prefer to send your own, we accept that too.

Questions about a model or a test? Email Amy Zhao, Export Manager, at info@halleffectthicknessgauge.com.

Check your own parts

Ask About Your Bottles or Containers

Tell us the material, the wall thickness range and the container size you need to measure. We reply within 24 business hours with the ball size and kit that fit your parts.

Your information is confidential and used only to prepare your quote.

Full specification and datasheet: KHT MTG-100 product page